Here kitty kitty, gain 15-20 RWHP and No Tune Required! with J&L HELLCAT Cold Air Intake. Direct fit for Dodge 2015-2020 6.2L Charger and Challenger.
J&L has jumped into the Hellcat intake market with both feet. We have owned a 2016 Hellcat Charger for nearly a year now and have been testing and designing this kit the entire time.
This kit includes a fully Roto Molded airbox that uses the factory fresh air (Ram Air) inlet from the grille/headlight that also seals to the hood. We feel this is the key component that puts our kit well above the rest. Not only does this box help keep inlet air temps down by blocking the filter from hot engine heat, it also helps hold in the cool air getting rammed in from the inlet creating a high pressure area around the filter.
Speaking of the filter, our filter is a custom built design made by S&B. It has a built in bell mouth for super smooth and fast air flow as well as huge 1" deep pleats for more surface area than filters that look much bigger.
The intake tube is roto molded plastic with a huge 125mm for superior airflow and NO heat soak like metal tubes.
With a mouth of 4.5" at the throttle body end, it is ready for any larger throttle bodies that may come in the future.
MAF and IAT adaptor plates: 2015/16 Hellcats have a Mass Air Flow sensor and 2017-2019 have an Inlet Air Temp sensor. We designed our kit to work with BOTH. Included in each kit are CNC machined aluminum plates, gasket and stainless screws to adapt to either model years.
HEAT SHIELD: Includes new roto molded plastic heat shield to block engine heat at idle and low speed.
RAIN SHIELDS: Each kit comes with custom designed and water jet cut Lexan shields that bolt to the hood grille. Not only do they keep rain from the filter, they allow the cooler rammed air to stay in the box around the filter VS just being pushed out of the grille.
FEATURES:
- Incorporates fresh air inlet from the grill.
- Uses a large area to make sure the filter has tons of cool air.
KIT INCLUDES:
- J&L Plastic Intake Tube
- Silicone Reducer
- 5x7 S&B Powerstack Air Filter
- Roto molded Heat Shield
- J&L MAF adaptor plate
- J&L IAT adaptor plate
- J&L Charger Rain Shield
- J&L Challenger Rain Shield
- HD Clamps, all needed hardware
- 2019 Hellcat PCV Kit
GAINS AND TESTING: 15-20 RWHP can be expected on a stock Hellcat. 25-30+ can be expected on a pulley and tuned Hellcat
TUNING: No tuning required
EASY INSTALL: The design, detailed instructions and online video (see below) helps make this an easy install
RACE FILTER: The Race filter is an optional filter, this filter IS NOT FOR STREET USE! It's no filtering media, with prolonged use it will allow contaminated that can damage your engine! J&L Oil Separators will not be responsible for any damage from use of Race filter. Customer assumes all risk!
J&L Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals!
This kit is 50 state legal. CARB E.O. No. D-761-5
Fitment
- 2015 Hellcat Charger
- 2016 Hellcat Charger
- 2017 Hellcat Charger
- 2018 Hellcat Charger
- 2019 Hellcat Charger
- 2020 Hellcat Charger
- 2015 Hellcat Challenger
- 2016 Hellcat Challenger
- 2017 Hellcat Challenger
- 2018 Hellcat Challenger
CA Residents: WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
